The Model Q45CT toroidal conductivity system is designed for on line monitoring of chemically aggressive process solutions. This sensor consists of two metallic ribbon coils that are fixed in place by the sensor jacket material. The drive coil is used to induce a current in the process solution. The second sensing coil is used to measure the current in the process solution, the magnitude of this current is proportional to the conductivity of the process solution.
Toroidal sensors are available in polypropylene, Kynar and PEEK to ensure sensor wetted materials are chemically resistant to process chemicals. Sensor material is also non-conductive, thereby isolating the sensor from electrical noise and ground loops that can influence the integrity of the measurement. This material also makes the sensor resistant to electrode coating, as most substances do not adhere to the sensor material.
Sensors can be submersion mounted for easy installation in open tanks or pipe mounted in the optional 2" tee fitting, which is keyed to the sensor for proper alignment. Tee fitting materials is either polypropylene or 316 stainless steel. For larger pipe diameters, the sensor can be insertion mounted through a 1 ½" NPT ball valve for easy retraction.
The Q45CT is also available as a Concentration Monitor. The monitor comes with concentration/temperature tables for sodium hydroxide, potassium hydroxide, hydrochloric acid, nitric acid and sulfuric acid. A user configurable table is also available for entering data points for a custom concentration curve.
The Model Q45CT toroidal conductivity system is well suited for aggressive chemical processes, water application that coat of foul traditional sensors and plating bath operations where high current densities are present.
Features
Non-Contacting Sensor: The non-contacting sensor contains two toroids that are isolated from the process by the body material, making the sensor resistant to foulants and electrical interferences.
Multiple Body Materials: The sensor body materials can be made of polypropylene, Kynar (PVDF), or PEEK.
Loop-powered, AC or Battery Versions: This line of microprocessor based instrumentation allows for easy implementation of loop-powered or battery-powered capability within the same instrument. This instrument can be rapidly converted between any of these versions with no requirements for software change.
- Loop-powered (16-35 VDC) Transmitter, 4-20 mA output
- Line-powered (115/230 VAC) Analyzer, dual relays, dual 4-20 mA outputs
- Battery-powered (VDC) Monitor/Data Logger, dual 0-2.5 VDC outputs
Standard PID Output: A PID control output is standard in every Q45CT monitor, with control parameters easily user configurable.
Dual Alarm Relays/Analog Outputs: AC operated systems provide two relays that are configurable for either "control mode" or "alarm mode" of operation and two analog outputs that are assignable for conductivity and/or temperature.
Flexible Calibration: Two point and sample calibration options include stability monitors to check temperature and main parameter stability before accepting data.
Large, Dual Line Display: The large, high contrast, super twist display provides excellent readability over a wide operating temperature range, even in low light conditions. The main display line consists of large, segmented characters with measurement units. The secondary display utilizes easily readable dot matrix characters for clear display of calibration and diagnostic messages. Two or four measured parameters may be displayed simultaneously.
Specifications - Monitor
| Measuring Range |
Main Input: 0.0 uS to 2000 mS % concentration
mg/L Total Dissolved Solids
Loop current 4.00 to 20.00 mA
Sensor temperature: -10 to 210°C |
| Main Parameter Range |
0 to 2,000 uS, 0.000 to 2.000 mS, 0.00 to 20.00 mS, 0.0 to 200.0 mS, 0 to 2000 mS, 0.0000 to 2.000S |
| Repeatability |
±3% or span or 0.1 uS whichever is greater |
| Sensitivity |
0.05% of span or 0.1 uS whichever is greater |
| Non-Linearity |
0.3% of span or 0.1 uS whichever is greater |
| Stability |
0.1% of span per 24 hours |
| Temperature Drift |
Span or zero, 0.03% of span/°C |
| Warm-Up Time |
7 seconds to rated performance |
| Response Time |
6 seconds to 90% of step input at lowest setting |
| Max Sensor to Analyzer Distance |
200 feet |
| Temperature Input |
Selectable Pt1000 to Pt100 RTD with automatic compensation |
| Filter |
Adjustable, 0-9.9 minutes additional damping to 90% step input |
| Output Isolation |
600 V galvanic isolation |
| EMI/RFI Influence |
Designed to EN 61326-1 |
| Location |
Designed for hazardous and non hazardous locations |
| Keypad |
4 key membrane type with tactile feedback, polycarbonate with UV coating, integral EMI/static shield and conductively coated window |
| Display |
Large, high contrast, Super-Twist (STN) LCD 4 digit main display with sign, 0.75" seven segment characters, 12 digit alpha numeric second line display, 5 x 7 dot matrix characters |
| Mounting Options |
Wall, panel or pipe/handrail |
| Conduit Openings |
3 M16 openings, cord grips and conduit adapter included |
| Temperature |
Service: -20 to 60°C
Storage: -30 to 70°C |
| Humidity |
0-95% RH, non-condensing |
| Weight |
Loop powered: 1 pound
Other configurations: 1.5 pounds |
| Enclosure |
Panel mount standard, NEMA 4X wall mount optional |
Specifications - Sensors
| Sensor |
Toroidal electrode |
| Wetted Materials |
Polypropylene, Kynar or PEEK |
| Sensor Cable |
20 feet standard, 200 feet maximum |
| Response Time |
90% in 2 seconds |
| Temperature Element |
Pt1000 RTD |
| Temperature Limits |
0-105°C |
| Pressure Limits |
0-150 psig |
| Process Connection |
¾" MNPT rear thread, optional 2" keyed tee fitting |
| Minimum Conductivity |
500 microSiemens |
Ordering Information
Other configurations available For pricing, please call AFC
International at 1-800-952-3293, 219-987-6825 or fax 219-987-6826 or
email sales@afcintl.com
| Description |
Catalog No. |
Q45CT Toroidal/Conductivity Monitor, 24VDC, 2 Wire, Polypropylene with 20' Cable
|
Q45CT-1-1-1
|
Q45CT Toroidal/Conductivity Monitor, 115 VAC with 2 Relays & 2
Outputs, Polypropylene with 20' Cable
|
Q45CT-2-1-1
|
Q45CT Toroidal/Conductivity Monitor, 24 VDC, 2 Wire, PEEK With 20' Cable
|
Q45CT-1-3-1
|
Q45CT Toroidal/Conductivity Monitor, 115 VAC with 2 Relays and 2 Outputs,
PEEK With 20' Cable
|
Q45CT-2-3-1
|
Downloads
Q45CT Toroidal Conductivity Monitor datasheet